ISOLADORES SUSPENSOS

SFH-1 & SFH-2 – Mola e fibra de vidro 

NEW 

Patented Self Centering Cap 

Epoxy Powder Coated Bracket and Spring Coil

How the self centering no short cap works: 

Indexed steps in spring cap correspond to standard  washer diameters for the appropriate rod diameter. The washer and rod stay centered in the cap 
 

Description 

Kinetics Model SFH Vibration Isolation Hangers consist of freestanding, large diameter, laterally stable steel springs in series with a precompressed molded fiber glass insert assembled into a stamped or welded hanger bracket.  To assure stability, the spring element has a minimum lateral spring stiffness of 1.0 times the rated vertical stiffness. 

Hangers will allow support rod misalignment through a 30° arc without short circuiting. 

Isolation brackets will carry a 500% overload without failure. Model SFH hangers are superior to hangers which incorporate a spring only, that can transmit noise through the all metal construction, and hangers incorporating noise stop pads only, that can transmit low frequency vibration which a spring would isolate. Hangers are available in deflections 1.04" to 2.20" (26 to 56 mm), and in capacities from 35 to 3500 lbs. (16 to 1588 kg). Kinetics Model SFH combination hangers are recommended for the isolation of vibration produced by suspended mechanical equipment, low speed suspended fans, transformers, ductwork, piping, etc. 

Application 

Kinetics Model SFH hangers are recommended for use near critically quiet areas for isolating any suspended source of both audible and inaudible noise and vibration. Suspended mechanical equipment such as in-line fans, cabinets fans, and piping and ductwork in close proximity to mechanical equipment are typical uses of Model SFH hangers.

High sound transmission loss ceiling systems can be effectively isolated by the use of Model SFH hangers in the ceiling suspension system. This hanger model is particularly suitable for use in isolated ceiling systems used to shield spaces from mechanical equipment rooms, flyover aircraft, and similar sound isolation involving predominately low frequency noise.

Standard Model SFH hangers are shipped fully assembled and ready for installation in threaded rod suspension systems.

Model SFH hangers are available in a wide range of load and static deflection selections and can be provided with labor saving accessories for adaptation to wire or strap suspension systems, and may be preloaded, or provided with plates for ease in erecting piping at a fixed elevation. 

Specifications 

Vibration isolators for suspended equipment with minimum static deflection requirement exceeding .4" (10mm), and where both high and low frequency vibration is to be isolated, shall be hangers consisting of a laterally stable steel spring in series with a precompressed molded fiber glass insert, complete with a load plate and assembled in a stamped or welded steel bracket.

The fiber glass insert shall be individually coated with a flexible, moisture impervious elastomeric membrane. The insert shall be molded from glass fibers with fiber diameters not exceeding .00027" (6.8 microns) and with a modulus of elasticity of 10.5 million PSI (738,223 kg/cm2 ).

Natural frequency of fiber glass vibration isolators shall be essentially constant for the operating load range of the supported equipment.

The spring element shall have a minimum lateral stiffness of 1.0 times the rated vertical stiffness.

Vibration isolators shall be color coded or otherwise identified to indicate load capacity.

The hanger bracket shall be designed to carry a 500% overload without failure and to allow support rod misalignment through a 30° arc without metal-to-metal contact or other short circuit.

The hanger bracket shall incorporate spring caps with indexed steps which correspond to the washer diameter of appropriately sized hanger rod to keep the rod centered in the spring cap and reduce rod misalignment. The spring caps are protected under U.S. patent number 5,653,426.

Isolation hangers shall be selected by the manufacturer for each specific application to comply with deflection requirements as shown on the Vibration Isolation Schedule or as indicated on the project documents.

The combination isolation hanger assembly with fiber glass insert shall be Model SFH, as manufactured by Kinetics Noise Control, Inc.